I suspect without the original source code you are going to struggle. I have a feeling that because of the amount of NOP’s in the code that there have been many on-line changes, this may explain all those, It probably needs spare space to download the small changes without shifting the whole program.

There is a mention in the manual about having to eventually download the whole program as the memory gets fragmented. This is the manual description. Use the correction of program code only when the source program cannot be used for special reasons.

If you are familiar with the basic set of instructions of program code, it is possible to correct an uploaded program. Naturally, the process is more difficult for a complex program than for a small program. The PLC is installed in a Scissor lift. I already tried to download the program whithout any changes in the mnemonic format STL. Thank you for your help, I wish you wouldnt say that I need the original code I will try my luck and see if I can get some information.

I looked through the manual and I could not find anything on PLC Errors however, If a fault light is showing then I would expect there is a way to check the PLC diagnostics, all the ones I have worked on have. Battery low, Divide by zero, program checksum etc. I tried to find the error, if I check the status it tells me: self diagnostics error: “Error code 1: Syntax error: ‘Self diagnosis’ provides details ” Then when I push the self diagnostics button: “Error 1 Syntax error in step 4.

October 29th, , PM parky. It really sounds to me that the program is damaged, probably find a lot more but it will only show the first error, as this is in step 4 then it definitely sounds like it would be un-recoverable. All times are GMT The time now is PM. Please DON’T use it for advertising, etc. Click here now to try it. User Name. Remember Me? Mark Forums Read. Page 1 of 2. Thread Tools. Specify the continuing pair entry. Continuing pair entry is selected on the Edit menu, by selecting Enter Continuing Pair.

The entry can also be specified in the following ways: – Using the keyboard. Click on. Specify the continuing number. When the continuing number dialog box is displayed, specify a number. Determine the position of continuing source right end. Either press the Return key at the position of continuing source right end , or click with the mouse. Determine the position of continuing destination left end.

When the position of continuing source right end has been determined, the message is displayed on the status bar. Either press the Return key at the position of continuing destination left end , or click with the mouse. The continuing pair entry is set at the specified number. Operation procedure for continuing symbol entry If Enter Continuing Symbol has been specified, move the cursor and determine the position of continuing source right end or the position of continuing destination left end.

Move the cursor to the position of continuing source right end. First, move the cursor to the position of continuing source right end. Specify the continuing symbol entry. The continuing symbol entry is selected on the Edit menu, by selecting Enter Continuing Symbol.

There is another way to specify the entry, besides using the menu: – Click with the right button of the mouse to display a menu from which the entry can be selected. The message is displayed on the status bar. Enter a two – digit continuing number. For example, to input No. Move the cursor to the position of continuing destination left end. Next, move the cursor to the position of continuing destination left end. To delete instructions and horizontal lines, move the cursor to the position of the instruction or horizontal line to be deleted, and press the key.

Move cursor to line to be deleted The line is deleted, and the cursor moves. Reference: To draw a horizontal line, press the key. Deleting vertical lines To delete a vertical line, move the cursor to the right of the vertical line to be deleted, and press the key. Move cursor to right of vertical line The vertical line is deleted. Reference: Pressing the key once again inserts a vertical line at that position. To add a relay on a horizontal line, it is not necessary to first delete the horizontal line; relays should be added on horizontal lines using the usual procedure.

In the example shown below, the R4 relay is being added to the horizontal line. Move cursor to position where relay is to be added Relay is added. Move the cursor to the position of the relay to be changed, and input the relay, using the usual procedure. In the example below, the X0 relay is changed to the X10 relay. Move cursor to position where Relay number is changed. Changing timer set value Move the cursor to the set value and change the value.

In the example below, K10 is changed to K Move cursor to position where Set value is changed. Reference: When the cursor reaches a position where the set value of timer can be changed, the current set value is displayed in the input field, and the function bar changes to a word display. Instructions can be inserted between instructions that have already been input. In the example below, the R4 relay is inserted in front of X0. Move cursor to insert position R4 relay is inserted in front of X0.

To insert the rung in an existing program, where additions or other changes will be made to the program, move the cursor to the position where the rung or rungs will be inserted, and then follow the procedure below.

Operation procedure 1. Move the cursor to the position where the rung will be inserted. Insert the rung. To insert the rung, select Insert a Rung on the Edit menu. The insertion can also be specified in the following ways: – Using the keyboard. To delete a blank rung which is no longer needed, move the cursor to the position of the rung to be deleted, and follow the procedure below.

An overview of the function for changing devices This function is used to change types and numbers of relays in a program, and to change operand and numbers of instruction, and other parameters. The remarks are not changed. Select the Change Device. To change a device, select Change Device on the Edit menu. Specify the item of the device to be changed. Specify the source device to the change and the range to which the change applies, as well as the destination device and the number from which the change is to start.

Then click on the Execute button. An overview of the XY word shift function This function is used to shift relay numbers and coil numbers in the program in word units. Select the Shift X and Y by Word. Specify the item of device X and Y to be shifted. Specify the area targeted for the shift, as well as the number following the shift, in word units. After Shift: 1 – 2] are specified, and then the Execute button is clicked.

To specify only the input relays [X] or only the output relays [Y], use the Change Device function described on the page 3 – Example: If the area of 0 to 1 has been specified as the target for the shift, this area will be targeted regardless of whether or not it is used in the program.

An overview of the PLC type changing function To shift a program which has been created to a different PLC type, the type targeted by the programming can be changed using the PLC type changing function if the two types have different settings.

Specify the PLC type to be changed. Make sure the PLC type change has been completed. If the PLC type has been successfully changed, the message shown below is displayed. If the system registers have been initialized, the following confirmation message is displayed. Press the OK button. CAUTION If there are certain instructions that cannot be used on the selected PLC type, or device numbers for areas that cannot be specified, a message like one of those shown below is displayed.

Examples of type change error messages. The range of device numbers in the program prior to the type change must match that of the type after the change. Make any necessary changes in the device number ranges. Any differences in the special data register DT and DT types will be converted automatically. The program capacities must also match. If necessary, delete part of the program prior to the change. If there are any instructions in the program prior to the change which cannot be used after the change, edit them before the change is made.

For high – level instructions, Configuration can be selected on the Option menu, and the Check the PLC Type of High – level Instruction check box in the displayed dialog box turned on or off to specify whether or not high – level instructions will be checked.

System registers are not initialized in the PLC type listed below, and should be initialized by the user if necessary. FP0 2. To use this function, the personal computer and the tool port of the PLC should be connected with a cable. Select the PLC to which the data is to be downloaded. This can also be done in the following ways: – Using the keyboard.

Confirm the dialog box message. When Download to PLC is selected, a dialog box like that at the left appears. To continue the downloading process, click on the Yes button. Confirm switching of the PLC operation mode. To switch to the PROG. Display during downloading The dialog box shown at the left is displayed while the program is being downloaded. If downloading is successfully completed, the dialog box shown at the left is displayed. To switch to the RUN mode, click on the Yes button.

Downloading to the PLC is completed. The program display switches to the monitoring status shown below. If the other PLC has no comment writing area, a dialog box like that shown will be displayed. Verified items include system registers, program sizes, program codes, and other data.

Select the Verify Program. The program to be verified is selected under Verify Program on the Debug menu. This can also be done in the following way: – Using the keyboard. Select the target to be verified. Select Verify Program to display the dialog box shown at the left. Select the target to be verified, and click on the Execute button to start the program verification.

Display of verification results When the verification is finished, the results are displayed. Explanation of this function If the two programs being verified have both been saved, first open each of the programs. Then press the button of the Target item in the Verify Program dialog box to specify a program name. The totally check program function works only in the PROG. There is a possibility that the contents of the program displayed on the screen are different from those of the program stored in the PLC, so always run the Verify Program function before running a totally check program function.

Select the Totally Check Program. Select the totally check program function by selecting Totally Check Program on the Debug menu. Run the totally check program function. When Totally Check Program is selected, a dialog box like that shown at the left appears. Clicking on the Execute button starts the totally check. The totally check results are displayed. If an error or errors exist, the number of errors, addresses and error contents are displayed.

Selecting highlighting the item to be searched and clicking on the Jump button jumps the cursor on the edit screen to the error address.

The settings for starting and stopping monitoring can be entered separately for each of the various windows. Operation procedure To start monitoring, select Online on the menu and then place a check mark by Start Monitoring in the displayed menu by clicking on it. Re – click to undo the checkmark and stop the monitor. Data can also be written and changed. Select the Monitoring Registers. Register monitoring is selected by selecting Monitoring Registers on the Online menu.

The registers monitoring window screen is displayed. When Monitoring Registers is selected, the following window is displayed. Register the device to be monitored. Pressing the [Enter] key at 1 the line number display column or 2 the registered device display column in the register monitoring window, or double – clicking with the mouse, displays the monitor device dialog box shown at the left. The above dialog box can also be displayed by Specify the type of device, the device number, selecting the following on the menu: Online and the number of registrations to be Monitor Setup Monitor Device Settings.

Clicking on the Base Number button, lets you specify the base number format to be used when data is displayed. Begin monitoring. After specifying the devices to be monitored, start monitoring in the online edit mode. This displays the values for the devices listed in 3 the monitoring display column of the register monitoring window. Key points Change the displayed radix. Either press the [Enter] key at 4 the monitor base number display column of the register monitoring window, or double – click with the mouse to display the monitor display format base number dialog box shown at the left.

The above dialog box can also be displayed using Specify the base number to which the the following menu operations: Online Moni- tor Setup Base Number Settings. It can also display format base number is to be be displayed by clicking on the Base Number changed, and click on the OK button in the register monitoring window de- button.

To use real – number monitoring, select a Dec Decimal or 2 words. Write the data. When using the online monitoring functon, either press the [Enter] key at 3 the monitor display column of the register monitoring window, or The above dialog box can also be displayed using the following menu operations: Online Moni- double – click with the mouse to display tor Setup Enter Value. Specify the value to be written, and click on the OK button.

Write a comment. Specify the comment, and click on the Entry button. If the various windows are enlarged to the maximum size, the program screen will be hidden behind the monitoring screen. This function can also be used to turn relays on and off. Select the relay monitoring function. The relay monitoring function is selected by selecting Monitoring Relays on the Online menu.

The relay monitoring window screen is displayed. When Monitoring Relays is selected, the following window is displayed. Relays can also be turned on and off. Register the relays to be monitored. Pressing the [Enter] key at 1 the line number display column or 2 the registered device display column in the relay monitoring window, or double – clicking with the mouse, displays the monitor device dialog box shown The menu operation selections Online Moni- at the left.

When continuous data elements are being registered together in one registration, set the number of items for the Entry Lines parameter. After specifying highlighting the devices to be monitored, start monitoring in the online edit mode. Key points Write the data.

When using the online monitoring function, either press the [Enter] key at 4 the monitor display column of the relay monitoring The above dialog box can also be displayed using window, or double – click with the the following menu operations: Online Moni- mouse to display the data writing tor Setup Enter Value.

Enter Value dialog box shown at the left. Set the value you wish to write and click the OK button. Specify the type of device targeted, the number, and the number of registrations Enter Lines , and click on the OK button. If two or more registrations are specified, the numbers are registered automatically in sequential order.

This turns the selected device on forcibly, regardless of the program contents. Clicking on the OFF 2 button turns the selected device off. Clicking on the FREE 3 button returns operation to that specified by the program. To turn the relay off, a forcible off should be executed for that relay, and then the relay should be canceled. Make sure sufficient attention is given to the status of peripheral devices and equipment before executing this function. If connected online, it also displays the running status of the PLC.

If an error occurs, this can be used to view the error content and to clear the error. Select the status display The status display is selected by selecting Status Display on the Online menu. The status display dialog box is displayed. Selecting Status Display displays the dialog box shown at the left. Operation errors, remote IO system errors, and other types of errors can be cleared. Syntax errors cannot be displayed or cleared. For operation errors, pressing Operation Err button displays the address for the error.

Depending on the PLC version, there may be times when error information cannot be displayed. Select Save to overwrite the previous file contents, and Save As Operation procedure Save To overwrite previous contents and save a program, select Save on the File menu. Operation procedure Save As 1. Select the Save As To save a program under a different file name, select Save As Selecting Save As Enter the new file name in the File name box, and click on the Save button.

Be aware of this when overwriting the contents of previously saved files. When the program is loaded at step 4 , it does not include any comments, so when it is overwritten and saved at step 5 , the comments are lost. Select the printing function. The printing function can be selected by selecting Print The printing dialog box is displayed.

When Print Check the printer to be used for printing, specify the printing range and number of copies to be printed, and click on OK button. In the default settings, only ladder diagrams are specified as the contents to be printed. If necessary, use the Print Style Setup parameters to select other items to be printed. Select the printing style settings. The printing style can be selected by selecting Print Style Setup on the File menu. The printing style dialog box is displayed.

When Print Style Setup is selected, the dialog box shown at the left is displayed. Place a check mark for those items to be printed. Key points To print data that includes comments, press the Detail button for the ladder, and place a check mark by the comment item. Explanation of this function To print a cover title, an item concerning the author, open Properties on the File menu, and fill in the Title and Author entries.

Key points Printing preview To view and check the image before it is printed, select Print Preview on the File menu, or double – click on Preview in the printing style settings dialog box.

Printing preview screen. Explanation of buttons : This initiates printing. They can be displayed on the screen and printed. These can be attached at the output coil position, and if the data is printed out, they are printed at the right side of the ladder diagram. They are not displayed on the screen. Block comments. These comments are attached to block unit explanations in the ladder diagram, and when input, are introduced between ladder diagrams.

Remark is printed here. Switching the comment display on the screen The following procedure is required in order to display the input comments on the screen. Select the comment display function. To display a comment on the screen, select Display Comment on the View menu. The comments are displayed.

All block comments are displayed. When saving program loaded from a PLC, make sure the correct operation procedure is used. PLC types to which comments are written FP2. Only if an optional comment memory has been installed FP2SH. Types with a comment memory FP3. Only if an optional ROM operation board or IC card board has been installed The volume of comments which can be written varies depending on the type.

PLC types to which comments cannot be written All types and cases other than those noted above. Cases in which comments are lost when a file is saved If the following procedure is carried out on a PLC that does not have a comment memory, any comments that have been entered will be lost. Key points Loading comments It is possible to read only comments from a file that has been saved. Operation procedure 1 Upload the program from the PLC.

Select Device Type, and align the cursor with the position at which the comment is to be input. Prepare to input the comment. Pressing the [Enter] key indents the area.

The system waits for input to be entered. Enter the comment. Enter the text and press the [Enter] key. This completes the input procedure. Key points If similar comments are being input consecutively, the following shortcut is convenient. Move the cursor. Move the cursor to the position right after where the block comment is to be input. Select the Enter Block Comment.

Select Enter Block Comment on the Comment menu. The block comment dialog box is displayed. Selecting Enter Block Comment displays a dialog box like that shown at the left. Enter the text in the input window and press the [Enter] key. When printed out, they are printed to the right of the bus line of the ladder diagram.

Move the cursor to the output coil position where the remark is to be input. Select the Enter Remarks. When using the PLC type FP0, programs assigned to an interrupt program task are no longer halted when a change in the program is made in online edit mode.

System register 46, , and has been corrected. The most important highlights at a glance:. Reuse of ready made functions and function blocks saves time for programming and debugging. Fewer errors through defined data types and encapsulation. Well-structured through programme organisation units, task- and projectmanagement.

Online monitoring and diagnostic.

 
 

 

Manual FPwin GR Ingles | PDF | Programmable Logic Controller | Menu (Computing)

 

Search Discontinued Products. Not requiring the use of a mouse for data entry, search, writing, monitoring and timer changes, all carried out only from the keyboard. Nais fpwin gr software download can be used to assist in positioning, PID instruction input, and FP-e screen display instruction input. Software are available for download. Asia-Pacific Middle East. Application Search.

Fiber Sensors Search by Specifications. FA Nais fpwin gr software download Support. Just add on nais fpwin gr software download your current system. Let’s start IoT! Search Keyword. Partly Order Discontinued September 30, Basic Information. The ladder programming software for FP series.

Easy field operations Not requiring the use of a mouse sotfware data entry, search, writing, nwis and timer changes, all carried out only from the keyboard. The software assets produced by using Ver. Downpoad by type, function instructions can be selected from the displayed list. Simple help included. Data from Excel and other applications can be copied and pasted via the clipboard.

Ссылка information concerning PLC usage situation and settings, and detailed information when an error occurs. Programs created gg the PLC of another company can be edited as text and then be transferred to the FP Series without difficulty.

A ladder diagram is displayed as a mnemonic code is entered from the keyboard. Communication via modem is easy страница FP Series units in isolated locations.

If you have any questions, please doftware the option below to contact us or find answers. Related Information.

 
 

Nais fpwin gr software download. PLCforum.uz.ua

 
 
replace.me GR7S PLC Software is the latest plc programming software for panasonic until the time I write this article (if you want to program IEC standard please use replace.me . WebDownloads. CAD data; Catalogs; Manuals; Software; Learn Our Products. INTRODUCTION TO AUTOMATION CONTROLS. Relays; Connectors; Switches; OUR . WebPLC laddder programming software for FP series. PLC ladder programming software for FP Series PLCs except FP7 and FP0H models. Characteristics Basic Ladder .